Joint arrangement in the assembly model

Top | Previous | Next

 

The command performs the arrangement of joints or other standard components in the assembly model. It is performed based on the iMate arrangement constraints pre-written in the component. The component is arranged based on the relevant geometry in the assembly model consistently specified for each assembly constraint. This command has a several default modes:

 

Single – where one geometric element is specified for one constraint in the model. An example can be a plane on which an axis is arranged: in this case, a component arranged to implement a constraint immediately changes its spatial position.

 

Multiple – where several geometric elements are specified for one constraint in the model. In this way, for the arranged component you may specify that its axis should be arranged based on several spatial planes. Then the command allows specifying a required geometry in the model for each assembly constraint, and inserting a new unit of the component being arranged in each available constraint realization position.

 

 

To open the command, go to:

 

Woodwork Design –> Joint –> Attach hardware_attachment32

 

 

 

Attach Joint

 

 

Select single entity

On-screen selection of a joint component inserted in the assembly.

W4I_Assembly_JointAttachment_PlaceComponent

Joint component selection from the specified catalogue on the disk. If an iPart component is selected, the component configuration window is opened and the user can select the required configuration of the inserted component. If an iPart component with a custom parameter is being inserted, the user can specify the member name and location on the disc.

 

iPart Component configuration window

iPart Component configuration window

   

iPart Component with Custom Parameter configuration window

iPart Component with Custom Parameter configuration window

 

 

If a component with Model State configurations is selected, a window will pop up with the option to select the desired configuration. At the bottom of the dialog all possible configurations of the assembly are displayed.

 

Specify Model State Configuration is a filter box where you can specify a number of criteria (separated by spaces); it filters out all the options and allows the user to narrow down the search for the required configuration. In the case shown in the figure, the 4 mm long clamps are filtered out and, in addition, the Minifix joints suitable for use on a 19mm long plate. This field has a drop-down list which stores the last filter values used.

 

Model State Config Window

 

W4I_Assembly_JointAttachment_UseLast

The use of the component last used in the command for performing the next arrangement. One of the five last inserted components can be selected from the dropdown list.

 

single_attachment24

Enabling the single arrangement mode.

 

multiple_attachment24

Enabling the multiple arrangement mode.

 

1.

A space where the iMate assembly constraints of the selected component are represented. Unchecked the box means cancellation of the selected assembly constraints and re-enabling selection of the specified constraint.

 

2.

Part Number of the component selected for insertion.

 

3.

Collapsing additional window displaying images that illustrate component insertion. The window presents images that illustrate component insertion. Registration of such images for a component is described below.
 

Flexible

If an iAssembly or assembly component is inserted, the dialogue displays a check box that allows assigning the flexible assembly status to such component.

 

The command is executed by clicking the "Attach" button.

 

hmtoggle_plus1Providing illiustration fo iMate arrangement constraints

 

In order for the inserted component to display illustrations explaining the operation and application of iMate arrangement constraint during the dialogue, such illustrating images have to be registered for the given component. If it is an iPart or an iAssembly, registration has to be performed while editing the images for their Factories.

 

A command is used to perform this

 

Manage –> Author –> iMate Figure Attach iMate Figure

 

 

iMate Figure attach

 

 

iMate Figure attach drop down List

 

In the drop down list, the user can choose iMate arrangement constraint in a given component and register the illustrating image selected from the disc for it. This image is incorporated into the component.

 

The "Common image" option is designed to register a generalized scheme, which generally explains the operating mechanism of a given component.

Select iMate Figure

 

If the illustration field is empty, the selection button starts a dialogue for selecting an image file from the disc and the user can register the preferred illustration.

Refuse iMate Figure

 

Cancels the given illustration image. The illustration field is emptied and the button switches to selection mode.

 

Important! Registration of an image means that the component is being edited. Therefore, the component must be placed in the workspace of the current Autodesk Inventor project.